Current post: Selling JDSU HST-3000 – We Buy New Used HST-3000 (‘s) Top Dollar Paid!

Selling JDSU HST-3000 – We Buy New Used HST-3000 (‘s) Top Dollar Paid!

If you’re looking to Sell JDSU HST-3000 Tester w/ E1 Module

JDSU HST-3000 Handheld Consumer Services Tester

Improving the installation, maintenance and troubleshooting of DSL services
With a market primed for broadband, operators are rapidly deploying DSL in their networks to deliver multimedia services over the existing copper wire in the local loop. Traditionally, one set of technicians performed individualized tests that qualified the copper while another set conducted DSL services testing and verification. In today’s market, however, operators can no longer afford the time, capital expense, and labor costs to conduct tests separately and incrementally. Furthermore, test solutions must generate results that have a strategic impact throughout an operator’s entire organization. This may include building customer loyalty by locating and fixing problems quickly, improving profitability by performing more tests with less staff, or leveraging workforce productivity by automating processes, methods, and procedures.
The Acterna HST-3000 is a modular handheld tester that can be built to order, to test the copper, test the DSL service and improve the process. Technicians use the HST-3000 copper base instrumentand the copper service interface module (SIM) to qualify, maintain, and troubleshoot the local loop. This same base instrument, with a second SIM that tests both ADSL and the copper, enables one technician to perform tests thatwere previously conducted by two technicians using different equipment.

For those technicians who only need to test ADSL, the instrument can be configured for ADSL functionality only. Any HST-3000 module equipped to perform ADSL service tests can also verify ISP and Internet connectivity with the Acterna Advanced IP Suite software option. With the HST-3000 minimize the time and reduce the capital expense and labor cost associated with ADSL and copper testing.

 

Highlights

  • A combined tester for Copper and DSL testing
  • Lower repeat rates with automated close out tests, scripting/pass-fail tests, and back office integration
  • Modular hardware and software architecture is flexible and easily upgraded
  • Laptop/PC integration via RS-232, USB, or wireless for easy results transfer
  • Intuitive, easy-to-use GUI, lightweight, rugged and water resistant

Instrument Interface Specifications

  • Dual TIP/RING and Ground POTS/Copper: Color-coded, shrouded 2mm “mini-banana” jacks
  • ADSL: 8-pin modular
  • 10/100 BT Ethernet jack: 8-pin modular
  • Serial port: DB9 female via cable (DCE)
  • USB Host
  • USB Device
  • Bluetooth short-range wireless

ADSL Standards

  • ANSI T1.413
  • ITU G.992.
  • 1 Annex A
  • ADSL over POTS
  • (G.DMT)
  • G.992.2 (G.Lite)
  • Cisco CAP

General Specifications

  • Ruggedness: Survives 3-ft drop to concrete on all sides
  • Water-resistance: Splash proof: may be used in heavy rain
  • Language: English
  • Keypad: Typical 12-button keyboard

Physical Specifications

  • Size (H x W x D): 9.5 x 4.5 x 2.75 in
  • Weight: 2.7 lb with battery
  • Operating temperature: 22°F to 122°F
  • Storage temperature: –40°F to 150°F
  • Battery life: 10 hrs. typical usage
  • Charging time: 7 hours from full discharge to full charge
  • Operating humidity: 10% to 80% relative humidity
  • Storage humidity: 10% to 95% relative humidity
  • Display: 1/4 VGA monochrome transflective, 3.8-in diagonal (readable in direct sunlight)

Buying, Selling, Trading JDSU HST-3000

JDSU HST-3000 E1 SIM Module

Dual E1RX/TX
Two separate receivers (RX) and transmitters (TX) allow for the simultaneous monitoring and evaluation of a wide range of alarms and errors. Different test modes with clock preferences support all of the requirements for ITU-T G.703 frame analysis, BERT, ITU-T G.821, ITU-T G.826, and ITU-T M.2100. This enables operators to validate connectivity and QoS quickly and efficiently.

E1 Pulse Shape Option
Incorrect pulse shape, due to jitter or incorrectly terminated interfaces, causes poor network performance. The Pulse Shape software option quickly assists in identifying network problems during installation, commissioning, or troubleshooting by comparing the pulsewith the ITU-T G.703 pulse mask.The software averages the received E1 pulse and automatically displays the result against the ITU-T mask.

FrameRelay Option
With the Frame Relay software option, technicians can verify that frame relay service is functioning properly by testing LMI activity, PVC/DLCI status, congestion, and lost framesto validate committed information rates(CIR).

Bidirectional Monitoring
The HST-3000 can monitor transmission passively in both directions to confirm physical layer and service level results on E1 Circuits.

If you’re selling your JDSU HST-3000 please fill out form on the right hand side of page.